Portable DIY 12V Battery Storage Spot Welder Pen Machine PCB Circuit Board

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
12V Portable Mini DIY Battery Energy Storage Spot Welder Pen PCB Circuit Board
Popular
Popular
Product Introduction
Product Features
Lightweight and portable, stable and reliable, wear-resistant, and can provides long service time.
Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by a short circuit.
Fuse the nickel sheet firmly with the battery.
And it is precisely controlled by the single-chip microcomputer program without a trigger switch.
Adopt screw fix, more stable, and more reliable.
The welding current approx. 90-130A, which is more than enough to welding a common 0.1mm-0.12mm nickel plate.
Upgraded to automatically triggered design, do not need to press the button for a long time anymore, completely frees your hands.
Note
Power supply requirements:
It is forbidden to use the power supply of the farad capacitor, and it is forbidden to use the lead-acid battery or lithium battery pack of 60A or above.
System voltage: 12V-14.6V (capacity X rate = must be greater than 150A)
Current requirements: 150A or more instantaneous output (such as car starter power supply, 3S RC high-power battery pack, 20A lead-acid battery with good performance above 20A)
Misunderstanding: Don't think that you can use 3 series 18650 series to supply power. After all, the conventional 18650 only has a 3-5C discharge rate, so each section can only provide
2.5A*3=7.5A load capacity, which is far from 150A unless 20 Parallel connection, 3 series, and 60 sections of 18650 are possible, but it is obviously unrealistic.
The battery pack that can start the car can basically meet the power supply requirements of this circuit.
The following battery packs can be used as working power:
1. 12V car starter power supply
2. Model 3S high rate battery pack
3. 3 string high rate lithium battery pack
4. Hitachi 40900 3-string battery pack
5. 12V 20A and above lead-acid battery with good performance
Switch function: press switch for 1.5 seconds to turn on (green light flash, output low power spot welding pulse every 3 seconds), press switch for 1.5 seconds (blue light flash, output medium power spot welding pulse every 3 seconds), press switch 1.5 Seconds (red light flash, high power spot welding pulse output every 3 seconds) Press the switch for 1.5 seconds to shut down.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
12V Portable Mini DIY Battery Energy Storage Spot Welder Pen PCB Circuit Board
Product Introduction
Product Features
Lightweight and portable, stable and reliable, wear-resistant, and can provides long service time.
Through the MOS tube output, this energy will be concentrated at the end of the welding pen, and it will be heated by a short circuit.
Fuse the nickel sheet firmly with the battery.
And it is precisely controlled by the single-chip microcomputer program without a trigger switch.
Adopt screw fix, more stable, and more reliable.
The welding current approx. 90-130A, which is more than enough to welding a common 0.1mm-0.12mm nickel plate.
Upgraded to automatically triggered design, do not need to press the button for a long time anymore, completely frees your hands.
Note
Power supply requirements:
It is forbidden to use the power supply of the farad capacitor, and it is forbidden to use the lead-acid battery or lithium battery pack of 60A or above.
System voltage: 12V-14.6V (capacity X rate = must be greater than 150A)
Current requirements: 150A or more instantaneous output (such as car starter power supply, 3S RC high-power battery pack, 20A lead-acid battery with good performance above 20A)
Misunderstanding: Don't think that you can use 3 series 18650 series to supply power. After all, the conventional 18650 only has a 3-5C discharge rate, so each section can only provide
2.5A*3=7.5A load capacity, which is far from 150A unless 20 Parallel connection, 3 series, and 60 sections of 18650 are possible, but it is obviously unrealistic.
The battery pack that can start the car can basically meet the power supply requirements of this circuit.
The following battery packs can be used as working power:
1. 12V car starter power supply
2. Model 3S high rate battery pack
3. 3 string high rate lithium battery pack
4. Hitachi 40900 3-string battery pack
5. 12V 20A and above lead-acid battery with good performance
Switch function: press switch for 1.5 seconds to turn on (green light flash, output low power spot welding pulse every 3 seconds), press switch for 1.5 seconds (blue light flash, output medium power spot welding pulse every 3 seconds), press switch 1.5 Seconds (red light flash, high power spot welding pulse output every 3 seconds) Press the switch for 1.5 seconds to shut down.
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.