Mini Spot Welder Machine 18650 Battery Welding Power Supply With Nickel Sheet

Description

Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Mini Spot Welder Machine 18650 Battery Welding Power Supply With Nickel Sheet
Popular
Popular
Product Introduction
Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.
3: Screen description and parameter adjustment.
4: Welding
Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.
Specifications:
Material: Metal
Input line length: app.20cm/7.87in
Length of welding pen: app.30cm/11.81in
Color: Red+Blue+Black
Battery: lithium battery(not included)
Quantity: 1Set
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
Nickel Sheet Plate
Description:
18650 Nickel Plated/Connected Plate
Main application: battery connection sheet, lead-out sheet, the product is mainly used in nickel-metal hydride batteries, lithium batteries, tabs, power tools, battery packs, polymer batteries, power batteries and instrumentation, telecommunications, vacuum, special light bulbs and other industries.
Material:Nickel
Size:thickness*width*length
0.1*5MM*10M
Package included:
1 X 10M 18650 Li-ion Battery Nickel Sheet Plate
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
Home
Electronic Component
Chips
Sensor
Arduino Module
Raspberry Pi
Mini Spot Welder Machine 18650 Battery Welding Power Supply With Nickel Sheet
Product Introduction
Portable DIY Mini Spot Welder Machine 18650 Battery Various Welding Power Supply
Features:
1. Wide selection of welding power supply: lithium battery power supply or 12V car battery.
2. The controller is controlled by a single chip microcomputer, and the output pulse is accurate to ensure the welding quality.
3. With LCD display screen, can display welding parameters.
4. The welding pen and the input line are connected by U-shaped cold-pressed terminals, which is convenient for disassembly and replacement.
5. Using automatic touch welding mode, while retaining the manual trigger interface, you can choose according to your own use.
6. The power board uses 2 Gusi copper to increase the overcurrent capacity.
7, using 5 300A MOS tubes, non-disassembled MOS tubes.
8. The MOS tube driver adopts the imported special chip driver. The fastest MOS tube can be hit with 20nS. The switch is fast to prevent the explosion of the tube and the non-triode push-pull drive.
9. The MOS drive design adds a transient diode to protect the MOS and prevent the explosion of the tube.
10. 10AWG multi-filament flexible wire is used for the welding pen line and the input line to increase the overcurrent capacity.
11.The controller is mainly for welding nickel-plated steel strips from 0.1mm to 0.15mm.
12. A 25V10000uF high-frequency low-resistance capacitor is added to the power input for energy compensation, which increases welding stability.
Spot Welding Machine Set only,other accessories demo in the picture is not included.
Instructions for use:
1: Power connection
The controller comes with a 20cm long 10AWG input wire. One end has been crimped with a U-shaped terminal, and the other end has not been processed. Connect the crimped U-shaped terminal to the control power input terminal, and the other end is processed according to its own power supply. Do not connect the negative electrode wrong.
2: Switch on and off
There is a power switch under the control board. After pressing, wait for 3 seconds. After the buzzer drops, the LCD lights up and the boot is complete. Press the power switch again to shut down.
3: Screen description and parameter adjustment.
4: Welding
Keep the welding pin clean. If the welding pin is polished into a round head, the welding effect can be improved. There are manual and automatic methods.
Specifications:
Material: Metal
Input line length: app.20cm/7.87in
Length of welding pen: app.30cm/11.81in
Color: Red+Blue+Black
Battery: lithium battery(not included)
Quantity: 1Set
Package Included:
1x Controller
1x Welding pen
1x Power input line (Red and Blue)
1 Pair x U-shaped cold-pressed terminal (used to connect to input power)
Several heat-shrinkable tubes, used to shrink the power input line
Notes:
Please allow 1-3 cm difference due to manual measurement.
Due to light and screen difference, the item's color may be slightly different from the pictures.
Nickel Sheet Plate
Description:
18650 Nickel Plated/Connected Plate
Main application: battery connection sheet, lead-out sheet, the product is mainly used in nickel-metal hydride batteries, lithium batteries, tabs, power tools, battery packs, polymer batteries, power batteries and instrumentation, telecommunications, vacuum, special light bulbs and other industries.
Material:Nickel
Size:thickness*width*length
0.1*5MM*10M
Package included:
1 X 10M 18650 Li-ion Battery Nickel Sheet Plate
Payment
Shipping
Refund
Payment
We accept PayPal only.
But we only
Accept
your
Ebay Address
,Please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Shipping
We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
Refund
All package need to
wait 30 days
(US only n
eed 7-10 days)
,
Please take care it.Less than 30 days,we can't take a refund
.
If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it.
If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.